Strip failed sealer, refill the joints, start fresh
Paver Restoration and Resealing in Kingsland, GA
Call (912) 600-8118 for a free estimate to restore cloudy or peeling pavers at your Kingsland home.
- Brings out deeper paver color
- Fresh joint sand helps lock pavers in place
- Gives weeds less room to grow
- Makes the surface easier to keep clean
- Free estimate, no obligation
Request a Free Estimate
Free, no obligation.
Who restores cloudy or peeling pavers around Kingsland?
A local contractor takes on paver restoration in Kingsland, GA, and you hear back inside 1 business day, usually much sooner. Looking over the damage is free, and you can decide afterward whether to go ahead. Photos of the worst spots speed things up. To start the conversation, call (912) 600-8118.
Restoration is for pavers where the old coat has gone wrong: milky, sticky, peeling or patchy, and the color underneath is hidden. The old sealer comes off, the joints get fresh sand and a new coat goes on. Most owners notice it first on the driveway after a wet summer. Describe what you see on the surface when you ask for a free estimate.
How do I know if my pavers need restoring and not only a rinse?
A Northeast Florida stripping company says pavers need stripping when they have turned white or hazy, the sealer is peeling or bubbling, or a past contractor used the wrong product. Signs of solvent sealer gone bad include a thick plastic-looking gloss, visible roller marks and pavers that looked good after sealing but whitened in the first few months. To check yours against that list, call (912) 600-8118.
When is a lighter reseal enough?
Pavers that are only faded or dull, with the sealer worn off naturally, are a lighter job. The same company says a standard clean and reseal is likely enough there. A contractor sorts one case from the other by looking at the surface, so send a photo or ask for a free estimate.
Why does sealer turn white or sticky in the first place?
Trapped moisture leads the list. A Tampa paver company says whitening, cloudiness and haze come from trapped water vapor, a coat laid too thick, poor surface prep or a new product that does not match the old one. A Northeast Florida page adds that humidity and ground moisture can make solvent sealers trap water, and that the problem does not fix itself. To talk through what happened on your driveway, call (912) 600-8118.
Does Kingsland weather make failure more likely?
Kingsland gives that problem plenty to work with. Wikipedia lists 84 percent average relative humidity and about 83 rainy days a year, and UGA Extension's Camden County office notes a high water table and often poorly draining soils. A coat put down while pavers were damp can fail within a season. To learn the cause on your pavers, ask for a free estimate.
Which communities near Kingsland get a restoration estimate?
A contractor can look at pavers in Kingsland and in each place listed below. Not seeing your street? Call (912) 600-8118.
Can new sealer go over the old coat?
Only if the old coat is sound. The Northeast Florida stripping page says sealing over a failed coat is not a fix, because new sealer cannot bond to a peeling, hazy or dirty surface, and the Tampa company says a failing coat must be fully stripped. Unilock adds a rule for sound coats: test that the new sealer is compatible with the old one. To have a contractor test yours, ask for a free estimate.
What does skipping the strip cost later?
The cost of skipping the strip shows up later, when the whole job is done twice. A contractor who wants to coat over milky pavers without a plan deserves a pointed question about what is holding the haze in. Bring that question to the phone at (912) 600-8118.
What is the restoration process, from strip to seal?
Most restorations run in the same order, each stage depending on the last. Ask for the steps in writing, then call (912) 600-8118 with questions.
1. Assess the coat
The contractor identifies the sealer type and how far it has failed, then covers or tapes off nearby surfaces.
2. Strip
A stripper matched to the paver goes on and sits. Water-based coats usually lift in one pass, and solvent coats or several layers may need two, a Northeast Florida page says.
3. Wash down to bare paver
The loosened sealer and stripper are rinsed off the surface, and a Tampa company says they should be recovered by vacuum, not left to run into the yard.
4. Fresh joint sand
Dry pavers get angular silica sand swept in and compacted, which locks them together again.
5. Reseal
Once everything is dry, a thin even coat goes on, with a natural or wet-look finish. A walk-through ends the visit.
What does paver restoration cost in Kingsland?
No Georgia company page found for this site lists a restoration rate, so the table is built from published pieces. Safe Touch in Northeast Florida lists $1.75 to $3.25 per square foot to clean, sand and seal and says strip-and-reseal sits higher when the old coat has failed. A Northeast Florida guide fills in the gap: stripping adds $0.75 to $1.50 per square foot. Add the two and you get the last column. To turn this into a figure for your pavers, ask for a free estimate.
What do stripping prices look like on their own?
Another view comes from a Northeast Florida stripping page, which says stripping alone runs from $350 for small areas up to $3,400 or more on large properties, with natural stone costing more than brick or concrete. Fully replacing joint sand adds $0.25 to $0.75 per square foot, says the guide, which also warns that bids under $1 per square foot usually skip prep. Compare any bid with these numbers, or call (912) 600-8118.
| Paved area | Strip old sealer | Clean, sand and seal | Both together |
|---|---|---|---|
| 300 sq ft | $225 to $450 | $525 to $975 | $750 to $1,425 |
| 600 sq ft | $450 to $900 | $1,050 to $1,950 | $1,500 to $2,850 |
| 1,000 sq ft | $750 to $1,500 | $1,750 to $3,250 | $2,500 to $4,750 |
| 1,500 sq ft | $1,125 to $2,250 | $2,625 to $4,875 | $3,750 to $7,125 |
Stripping: $0.75 to $1.50 per square foot, Hydro Wash 360 guide. Clean, sand and seal: $1.75 to $3.25 per square foot, Safe Touch, Northeast Florida. Both are Florida figures because no Georgia page found posts one.
How long does a paver restoration take?
Plan on a day or two. A Northeast Florida stripping page says most standard jobs take one full day, and Safe Touch calls sanding and sealing pavers a two-day restoration, not a same-day spray. Pavers must dry between stages, so a rain-free window matters more than the calendar. To find an open window, call (912) 600-8118.
When can feet and cars return?
Traffic comes back in steps. The same page allows foot traffic within 24 hours of the new sealer and vehicles within 48 to 72 hours, depending on weather and product. Unilock wants the sprinklers off while the coat cures. Ask for a return date for the cars when you ask for a free estimate.
Which weather is right for resealing after restoration?
Unilock advises 50 to 90 degrees, with about 75 ideal, and 24 to 48 hours of clear skies before sealing and up to 48 hours dry after. Kingsland's July mean high is 91 degrees, according to Wikipedia, so a hot afternoon may be too much, and a morning or a milder week is the safer pick. Pavers in cooler shade can take about a day to dry. To plan around the forecast, call (912) 600-8118.
Will restoration fix pavers that sank or shifted?
No. Stripping and sealing change the surface, not the base. Pavers that rock or hold a puddle need their bed reworked first, and UGA Extension points to high water tables and poorly draining soils on this coast. Ask whether leveling is part of the bid, then ask for a free estimate.
When should restored pavers be sealed again?
Unilock puts the reseal window at three to five years, and a Northeast Florida guide puts driveways and pool decks closer to three and shaded patios closer to five. A coat on a restored surface that looks cloudy after a few months is a warning, not an ordinary wear sign. To schedule a check, call (912) 600-8118.
What do restored pavers look like in Kingsland?
Questions Kingsland homeowners ask about paver restoration
Can I clean sand and seal my pavers?
A contractor can, and for a failed coat it becomes a restoration. Safe Touch describes paver sanding and sealing as a two-day restoration, not a same-day spray. The pavers must dry fully before and after the sand goes in. A coat that has already turned white has to come off first.
How much to clean and seal pavers?
In Northeast Florida, published prices run $1.75 to $3.25 per square foot to clean, sand and seal, and a guide adds $0.75 to $1.50 per square foot when old sealer must be stripped. No Georgia company page found for this site posts a rate, so that is the honest range to measure bids against.
Should you seal pavers after power washing?
After a wash and fresh joint sand, yes, if the plan is a restored finish. The pavers must be dry, and Unilock says to sweep all loose sand off the surface because sealer traps whatever is left. A Tampa company also says to strip any failing coat before the new one goes down.
How long do paver sealers last?
Unilock says three to five years in general, and solvent products can last four to five when maintained. A Northeast Florida guide puts driveways and pool decks nearer three years. When sealer goes cloudy within months, it failed early and needs to be stripped, not recoated.
Why did my sealed pavers turn white?
Moisture is the usual suspect. A Northeast Florida stripping page says humidity and ground moisture can make solvent sealers trap water and turn white, and that it does not stop on its own. A Tampa company lists a thick coat, poor prep and an incompatible product as other causes.
Do I have to strip old sealer before resealing?
Not always. If the coat is only worn and faded, a standard clean and reseal is likely enough, says a Northeast Florida stripping page. If it is white, hazy, peeling or bubbling, stripping comes first. Unilock also advises testing whether the new sealer is compatible with the old one.
How long until I can drive on a resealed driveway?
One stripping page says foot traffic is allowed within 24 hours and vehicles within 48 to 72 hours, depending on weather and product. Unilock asks for up to 48 hours of dry weather for the sealer to cure. Ask the contractor for the exact day cars can go back.
Does Kingsland's wet ground affect paver restoration?
It can. UGA Extension's Camden County office points to high rainfall, a high water table and often poorly draining soils on the coast. Pavers that sit over soggy ground may hold moisture, so a contractor checks dry time with care before resealing.
What other paver services are available near Kingsland?
Want a free look at your Kingsland pavers?
Call or fill in the short form, and a local contractor responds inside 1 business day, usually much sooner.
Free, no obligation